http://wiki.signature.net/index.php?action=history&feed=atom&title=The_SYSGEN_configuration_utility%2FSpoolers 2026-05-04T00:49:49Z Revision history for this page on the wiki MediaWiki 1.16.0 http://wiki.signature.net/index.php?title=The_SYSGEN_configuration_utility/Spoolers&diff=922&oldid=prev 2009-05-30T13:49:12Z

<p>New page: &#39;&#39;&#39;[SPOOLERS]&#39;&#39;&#39; Minimum Requirements: . This group is not r...</p> <p><b>New page</b></p><div>'''[SPOOLERS]'''<br /> <br /> Minimum Requirements: <br /> .<br /> This group is not required.<br /> .<br /> Refer to the minimal INI file to see the minimum requirements to configure Comet.<br /> <br /> The SPOOLERS group contains information about the configured print spoolers. The group contains one segment title:<br /> <br /> ''' '' Spool = spooler-name,path;''''' <br /> <br /> For example:<br /> <br /> [SPOOLERS]<br /> <br /> Spool = SP1,FS1\SYS:\COMET\QSPOOL\; spool on primary file server<br /> Spool = SP2,FS2\SYS:\COMET\QSPOOL\; spool on secondary file server<br /> Spool = SP3,C:\COMET\QSPOOL\; spool on local hard disc<br /> Spool = SP4,D:\COMET\RAM\; spool on local RAM disc<br /> Spool = SP5,\\SERVER\SYS\COMET\QSPOOL\; UNC path example (see Directories)<br /> Spool = SP6,SERVER\SYS:\COMET\QSPOOL Network type &quot;S&quot; example<br /> Spool = SPL,L:\COMET\QSPOOL; Network type &quot;N&quot; example<br /> <br /> '''Segment Title'''<br /> <br /> Spool = spooler-name,path;<br /> <br /> This segment title has two parameters. They are: <br /> <br /> ''' spooler-name'''<br /> <br /> Enter the spool device name in the form:<br /> ''SPx'' (where x can be a number from 1 through 9), or<br /> ''Sxx'' (where xx can be any alphanumeric characters)<br /> <br /> For those printers that are configured for exception or automatic, any spool device name can be attached.<br /> <br /> '''path'''<br /> <br /> Enter the full DOS path where the spool files are to be created. The DOS path must be a valid Comet directory path that contains the QDIR files. The path can contain up to 60 characters.<br /> <br /> The path should always end with the “\|” character. However, if you don’t include this character, SYSGEN will add one when the INI file is processed.<br /> <br /> Spool files should not be created on directories that contains standard Comet release files, including the following directories:<br /> <br /> REL<br /> UTL<br /> MTB<br /> UTR<br /> CED<br /> HLP<br /> <br /> '''Initializing a Spooler'''<br /> <br /> You must run the QSPOOL utility initially of any print spooler that has been just created or it's DOS path has been changed. This is a mandatory step in order for Comet to build it's own working files. To initialize a new or changed spooler, do the following: <br /> <br /> *Build a new spool entry INI record, or change an existing spool INI record <br /> *Generate a new CFG configuration file <br /> *Exit Comet <br /> *Restart Comet <br /> *Run the QSPOOL utility Perform a print job inquiry on the new/changed spool device</div>

Badge